[Oct 24, 2022] Verified 300-430 dumps and 160 unique questions
300-430 Dumps for Pass Guaranteed - Pass 300-430 Exam 2022
There are eight topics of interest for the Cisco 300-430 exam. They represent the content that the test is most likely to include. Alongside the weighted percentages, here is more comprehensive coverage of the objectives:
- QoS on a Wireless Network (10%)
This objective takes care of four areas of capabilities that are all critical to wireless networks. The first one is on implementing QoS schemes while considering the requirements, which can include wired-based to wireless-based mapping. The next one encompasses implementing QoS targeted at the wireless clients. The final portion is on executing AVC that includes Fastlane (and this is only on WLC).
- Multicast (10%)
In this topic, there are five key areas. They include implementing multicast components, describing the effect of multicast on wireless networks, and implementing multicast on WLAN. Others are executing mDNS and Multicast Direct.
- Device Hardening (10%)
This is the final domain of the Cisco 300-430 exam. You should know how to implement access controls for devices, including TACAS+ and RADIUS. Another thing is executing authentication of access points such as 802.1X. Another subtopic is concerning the implementation of CPU ACLs upon the controller.
- Monitoring (15%)
This topic area is about utilizing reports concerning PI and Data Center for Cisco. It is also about managing alarms as well as rogues like APs in addition to the clients. WLC, PI, and Cisco Data Center are the technologies you should know as well. Moreover, the candidates must familiarize themselves with managing RF Interferers. Another field is on troubleshooting client connectivity where it involves WLC, ISE, PI, and Cisco’s Data Center as well.
- FlexConnenct (15%)
This domain is significant to supporting the learners in skills such as deploying components of FlexConnect that include switching and modes of operation. It also extends to deploying FlexConenct capabilities, for example, roaming and groups, fault tolerance and split tunnelling, Flex ACL and central switching, which is VLAN-based. Other aspects of this subject concern upgrading smart AP image and implementing Office Extend.
- Security for Wireless Client Connectivity (20%)
This objective is about configuring the clients’ profiling on ISE and WLC. Next, it concerns implementing BYOD as well as guests and includes CWA utilizing ISE, LWA with WLC or ISE, provisioning of native supplication using ISE, provisioning of a certificate on a controller, and executing 802.1X in addition to AAA on varied wireless infrastructures and ISE. The last issue concerns executing networking that is identity-based on varying wireless infrastructures, such as QoS, VLANs, and ACLS.
- Location Services (10%)
This area involves deploying MSE in addition to CMX on a network that is wireless-based. It also has to do with implementing location services where it encompasses client tracking, RFID tags (only tracking), inteferers, rogue APs, and clients.
NEW QUESTION 67
Which two restrictions are in place with regards to configuring mDNS? (Choose two.)
- A. mDNS cannot use UDP port 5353 as the destination port.
- B. mDNS is not supported on FlexConnect APs with a locally switched WLAN.
- C. mDNS is not supported over IPv6.
- D. Controller software must be newer than 7.0.6+.
- E. mDNS uses only UDP port 5436 as a destination port.
Answer: B,C
Explanation:
NEW QUESTION 68
An engineer set up identity-based networking with ISE and configured AAA override on the WLAN. Which two attributes must be used to change the client behavior from the default settings? (Choose two.)
- A. IPv6 ACL
- B. DSCP value
- C. DNS server
- D. DHCP timeout
- E. multicast address
Answer: B,C
NEW QUESTION 69
Refer to the exhibit.
An engineer must connect a fork lift via a WGB to a wireless network and must authenticate the WGB certificate against the RADIUS server. Which three steps are required for this configuration? (Choose three.)
- A. Configure WGB as a network device in ISE.
- B. Configure the certificate on the WLC.
- C. Configure a policy on ISE to allow devices to connect that validate the certificate.
- D. Configure the access point with the root certificate from ISE.
- E. Configure the certificate, WLAN, and radio interface on WGB.
- F. Configure WLAN to authenticate using ISE.
Answer: C,E,F
NEW QUESTION 70
When configuring a Cisco WLC, which CLI command adds a VLAN with VLAN ID of 30 to a FlexConnect group named BranchA-FCG?
- A. config flexconnect group BranchA-FCG vlan 30 add
- B. config flexconnect BranchA-FCG vlan 30 add
- C. config flexconnect BranchA-FCG vlan add 30
- D. config flexconnect group BranchA-FCG vlan add 30
Answer: D
Explanation:
NEW QUESTION 71
Refer to the exhibit.
A network administrator deploys the DHCP profiler service in two ISE servers: 10.3.10.101 and 10.3.10.102. All BYOD devices connecting to WLAN on VLAN63 have been incorrectly profiled and are assigned as unknown profiled endpoints. Which action efficiently rectifies the issue according to Cisco recommendations?
- A. Nothing needed to be added on the Cisco WLC or VLAN interface. The ISE configuration must be fixed.
- B. Keep DHCP proxy enabled on the Cisco WLC and define helper-address under the VLAN interface to point to the two ISE servers.
- C. Disable DHCP proxy on the Cisco WLC and run the ip helper-address command under the VLAN interface to point to DHCP and the two ISE servers.
- D. Disable DHCP proxy on the Cisco WL
Answer: C
Explanation:
https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/110865-dhcp-wlc.html
NEW QUESTION 72
After looking in the logs, an engineer notices that RRM keeps changing the channels for non-IEEE 802. 11 interferers. After surveying the area, it has been decided that RRM should not change the channel. Which feature must be enabled to ignore non-802.11 interference?
- A. Avoid Persistent Non-WIFI Interference
- B. Avoid Non-802. 11 Noise
- C. Avoid Foreign AP Interference
- D. Avoid Cisco AP Load
Answer: A
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/configure-guide/b_wi_16_10_cg/radio-resource- Check the Avoid Non-802.11a (802.11b) Noise check box to cause the controller's RRM algorithms to consider noise (non-802.11 traffic) in the channel when assigning channels to lightweight access points, or uncheck it to disable this feature. For example, RRM may have access points avoid channels with significant interference from nonaccess point sources, such as microwave ovens. The default value is selected.
Check the Avoid Persistent Non-WiFi Interference check box to configure the controller to stop ignoring persistent non-Wi-Fi interference in new channel calculation. The persistent non-Wi-Fi interference is considered during the metric calculation for channels.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-6/config-guide/b_cg86/radio_resource_management
NEW QUESTION 73
A corporation has a wireless network where all access points are configured in FlexConnect. The WLC has a Data WLAN and a VoWiFi WLAN implemented where centrally-switched is configured for the APs. Which QoS configuration must be implemented for the wireless packets to maintain the marking across the wired and wireless network?
- A. Set QoS to Platinum
- B. Enable CAC
- C. Allow WMM
- D. Trust DSCP
Answer: D
Explanation:
NEW QUESTION 74
Refer to the exhibit.
A wireless engineer has integrated the wireless network with a RADIUS server. Although the configuration on the RADIUS is correct, users are reporting that they are unable to connect. During troubleshooting, the engineer notices that the authentication requests are being dropped. Which action will resolve the issue?
- A. Allow connectivity from the wireless controller to the IP of the RADIUS server.
- B. Configure the shared-secret keys on the controller and the RADIUS server.
- C. Provide a valid client username that has been configured on the RADIUS server.
- D. Authenticate the client using the same EAP type that has been set up on the RADIUS server.
Answer: A
NEW QUESTION 75
An engineer configured a Cisco AireOS controller with two TACACS+ servers. The engineer notices that whenthe primary TACACS+ server fails, the WLC starts using the secondary server as expected, but the WLC doesnot use the primary server again until the secondary server fails or the controller is rebooted. Which cause ofthis issue is true?
- A. DNS query is disabled
- B. DNS query is enabled
- C. Fallback is enabled
- D. Fallback is disabled
Answer: D
NEW QUESTION 76
An enterprise has recently deployed a voice and video solution available to all employees using AireOS controllers. The employees must use this service over their laptops, but users report poor service when connected to the wireless network. The programs that consume bandwidth must be identified and restricted.
Which configuration on the WLAN aids in recognizing the traffic?
- A. AVC Profile
- B. QoS Profile
- C. Application Visibility
- D. NetFlow Monitor
Answer: C
NEW QUESTION 77
Which three characteristics of a rogue AP pose a high security risk? (Choose three.)
- A. open authentication
- B. foreign SSID
- C. high RSSI
- D. low RSSI
- E. distant location
- F. accepts clients
Answer: A,B,F
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/controller/74/configuration/guides/consolidated/b_cg74_CONSO
NEW QUESTION 78
Which component must be integrated with Cisco DNA Center to display the location of a client that is experiencing connectivity issues?
- A. Cisco Connected Mobile Experiences
- B. Cisco Mobility Services Engine
- C. Wireless Intrusion Prevention System
- D. Cisco Hyperlocation Module
Answer: A
Explanation:
NEW QUESTION 79
A wireless network engineer must present a list of all rogue APs with a high severity score to senior management. Which report must be created in Cisco Prime Infrastructure to provide this information?
- A. Rogue APs
- B. Rogue AP Events
- C. New Rogue APs
- D. Rogue AP Count Summary
Answer: B
NEW QUESTION 80
What is the default NMSP echo interval between Cisco MSE and a Wireless LAN Controller?
- A. 10 seconds
- B. 30 seconds
- C. 15 seconds
- D. 60 seconds
Answer: C
NEW QUESTION 81
An engineer is tuning RRM parameters to improve client connectivity. Which channel band results in the best
802.11n client compatibility?
- A. UNII-1
- B. UNII-2
- C. UNII-3
- D. UNII-2e
- E. UNII
Answer: A
Explanation:
802.11n operates on the same channel as 802.11a. For better compatibility with 802.11n clients, it is recommended to stay on lower channels (UNII-1 band).
Reference: http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/108184- config-802-11n-wlc.html
NEW QUESTION 82
When using a Cisco Catalyst 9800 Series Wireless Controller, which statement about AutoQoS is true?
- A. It has a set of predefined profiles that you cannot modify further
- B. It automates deployment of wired QoS and makes wireless QoS implementation easier
- C. It matches traffic and assigns each matched packet to QoS groups
- D. It allows the output policy map to put specific QoS queues into specific subgroups
Answer: C
Explanation:
NEW QUESTION 83
A corporation has a wireless network where all access points are configured in FlexConnect. The WLC has a Data WLAN and a VoWiFi WLAN implemented where centrally-switched is configured for the APs. Which QoS configuration must be implemented for the wireless packets to maintain the marking across the wired and wireless network?
- A. Set QoS to Platinum
- B. Enable CAC
- C. Allow WMM
- D. Trust DSCP
Answer: D
Explanation:
NEW QUESTION 84
Which two events are outcomes of a successful RF jamming attack? (Choose two.)
- A. deauthentication multicast
- B. deauthentication broadcast
- C. disruption of WLAN services
- D. physical damage to AP hardware
- E. unauthentication association
Answer: C,D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/mse/3350/72/wIPS_Configuration/Guide/wIPS_72/msecg_appA
NEW QUESTION 85
......
Cisco 300-430: Details + Topics
This test is also called Implementing Cisco Wireless Networks or ENWLSI. It is among the concentration exams for CCNP Enterprise that you need to choose from. You select it from a list of tests that also include Cisco 300-410, Cisco 300-415, Cisco 300-420, Cisco 300-425, and Cisco 300-435. The 300-430 exam is offered in English and Japanese only, and you will have 1 hour and 30 minutes to deal with about 60 questions. The expected question formats include testlets, multiple choice, and fill-in-the-blank.
The Cisco 300-430 exam is administered through Pearson VUE and the registration fee is $300. The official passing score is 825 points, so try to earn more than that. If you want to schedule this test, you have to create an account on the Pearson VUE platform and follow the instructions up to the end.
Topics of Cisco 300-430: Implementing Cisco Enterprise Wireless Networks Exam
These core topics of 310-430 practice test listed below are general recommendations for the material that is likely to be used for the examination. However, on any delivery of the test, other similar topics could also appear. The guidelines below can update at any time without notice to better represent the contents of the 310-430 exam dumps pdf and for clarity purposes.
It is recommended that, where possible, the applicant use these courses and/or other resources to provide background information on the exam objectives. The syllabus for the Cisco 300-430: Implementing Cisco Enterprise Wireless Networks examination is listed below in detail for each section of 300-430 exam dumps:
- Implement Authentication, Authorization, and Accounting (AAA) Services for Central Mode WLANs
- Implement AAA Services for FlexConnect Mode Wireless LANs (WLANs)
- Configure Cisco Application Visibility and Control (AVC) in the Wireless Network
- Capture Successful Client Authentications
- Implementing and Troubleshooting Quality of Service (QoS) in Wireless Networks
- Configure Bring Your Own Device (BYOD) in the Wireless Network
- Capture Successful QoS Traffic Marking in the Wireless Network
- Implementing and Troubleshooting Advanced Wireless Network Services
- Capture a Successful AP Authentication
- Configure multicast DNS (mDNS) in the Wireless Network
- Configure, Detect, and Locate Services on the Cisco CMX
- Customize Cisco Prime Infrastructure for Network Monitoring
- Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR)
- Configure QoS in the Wireless Network for Voice and Video Services
- Configure Guest Services in the Wireless Network
Latest 100% Passing Guarantee - Brilliant 300-430 Exam Questions PDF: https://exams4sure.actualcollection.com/300-430-exam-questions.html